Bendix offers spring fleet maintenance tech tips

Bendix offers spring fleet maintenance tech tips

Bendix shares tips to allow fleets to hit the road with enhanced safety, uptime, and peace of mind this spring, by addressing winter’s toll on your trucks.

Wild temperature swings, icy roads, treatment chemicals and other ravages—winter takes a toll on commercial vehicles. Bendix wants you to know that while spring in North America can be a cause for celebration, it’s also the time to tackle preventive maintenance to keep your fleet on the road. Here are some of the company’s spring fleet maintenance tips.

Air matters

Winter weather can be punishing on the physical components of a truck’s air brake system, according to Bendix. This situation is especially true if the vehicle travels through temperature changes with freeze-and-thaw cycles. Coming out of winter, drivers and technicians should pay extra attention to component performance.

“Take the air system, for example,” said Jason Kolecki, Bendix director of marketing and customer solutions, air supply and drivetrain. “As more trucking systems depend on a reliable supply of clean and dry compressed air – including automated manual yransmissions (AMTs), emissions controls, and full stability – proper maintenance of the air system after winter is key to keeping vehicles on the road and in good operating condition.”

What should you look for? Bendix says air dryers mounted on the frame rail are susceptible to corrosion because of their exposure to the road—this scenario is particularly true of the seats around the purge and pressure protection valves, as well as the governor connection. Water can mix with dirt, sand, and road chemicals and form residue that can clog purge and pressure protection valves and other air dryer parts – which Bendix says will prevent proper performance. In addition, steel air tanks can also corrode and develop small punctures. During inspections, keep an eye out for cracking or breakage of plastic air-line tubing that connects the dryer to the truck’s air system. Chemicals and temperature cycling can also affect push-to-connect air fittings.

According to Kolecki, air leaks may be present even if they’re unseen or unheard. “A good indication that your system may be losing air is if charging the tanks takes significantly longer—three or four minutes, for example, as opposed to one or two,” he said. “The same is true if the system is charging more often. Increased charging cycles means more air going through the dryer, which affects the life of the dryer cartridge.”

Bendix recommends the air dryer cartridge be serviced yearly. If the air dryer cartridge wasn’t switched out in the fall, then spring is a good time to replace it. Remember to replace oil-coalescing cartridges like-for-like, Bendix says.

Brake care

“When it comes to brakes, after winter, you are looking for corrosion, damage, and missing or loose components – not unlike any standard inspection,” said Mark Holley, Bendix director of marketing and customer solutions, wheel-end.

Examine brake friction for good condition—no lining cracks, missing portions, oil or grease contamination and minimum thickness. If it’s time for new friction, Bendix says to to stay up to spec: Not all friction that is marketed as “acceptable” under current Reduced Stopping Distance (RSD) regulations will actually perform to that standard. Select components that will ensure that OEM requirements are met so the vehicle remains compliant. If the friction needs to be replaced, it must be replaced on both sides of the axle.

“For brake chambers, make sure the dust plugs are seated properly to prevent corrosive materials from getting inside and causing internal damage,” Holley said. “Technicians should also measure chamber stroke at each wheel-end to ensure proper brake adjustment. In addition, examine the air lines – you want to see that everything is tied up properly and that there is no chafing. Check for damage in the mounting mechanism as well.”

On vehicles with air disc brakes, examine the rotor for corrosion and to be sure the cooling fins are not plugged up, which would prevent the rotor from cooling properly. Inspect the chamber for damage or corrosion, and look at the air hoses and clamping mechanism to ensure they’re intact.

“We advise technicians to inspect the boots for punctures or tears too, as any opening into the caliper can lead to corrosion,” Holley said. “And check the integrity of the guide pins. Replace parts where necessary, and make sure the shear adapter cover is in place and fully seated. The pads should move freely in the carrier, so you should remove them and clean the carrier surface with a wire brush, if necessary. Also check to ensure that the brake moves freely on its guidance system.”

Holley continued, “For brakes overall, the importance of lubrication can’t be overstated: It keeps moisture from building up and enabling corrosion. Coming out of winter, newly grease all your automatic slack adjusters, clevis pin connections, cam tubes, shafts and bushings.”

Ensure optimized valve performance

Bendix adds that the feel of the brakes is also important. Sometimes, it may feel as if they’re responding more “slowly” to the driver’s push of the brake pedal. This feeling may indicate valve seals in the system that have had their lubricant degraded through corrosion – or possibly by the use of de-icing solutions if the air system froze during the winter.

“We recommend not adding brake anti-freeze compounds to the air system, but understand that sometimes it’s unavoidable for getting trucks back on the road quickly and safely,” Holley said.

If you’ve had to use a de-icing solution, then spring is a good time to check for leaks around brake valves where O-rings might have been exposed to the chemicals. Now is also a good time to replace valves that may be sticking internally because of loss of lubrication. Some fleets routinely change out air valves as part of post-winter preventive maintenance.

Advanced Driver Assistance Systems (ADAS) technologies

Technologies like ABS and electronic stability control (ESC) are not immune to rough winter conditions. “One ABS concern centers on wheel-speed sensors, which can be susceptible to chassis harness issues,” said TJ Thomas, Bendix director of marketing and customer solutions, controls. “Wire harnesses can get damaged by chafing, gravel or corrosion. Any wiring on the chassis can be at risk because once a damaged wiring harness gets wet, it is more likely to short out. A common source of calls to the Bendix tech support team this time of year is post-winter electrical shorts and the brake system component malfunctions that result.”

Frayed or cut chassis wires can also cause potential issues with the ADAS camera or radar. Bendix advises checking the chassis harness and connectors near the ADAS camera or radar should a problem with the system be detected or if the system doesn’t seem to be working optimally.

“An issue that may arise for stability control can be the steering angle sensor out of calibration, which can sometimes happen after a front-end alignment,” Thomas said. “It’s important to calibrate the steering angle sensor after almost any work is done on the front end.”

Radar units face their own challenges. Since the radar is on the front of the vehicle, Bendix explains that the connector can be exposed to all sorts of chemicals—which is especially true in winter when salt and other substances are used on roads. It’s a good practice to make sure the connector is properly covered, sealed, and secured to help minimize corrosion that may occur from repeated exposure to moisture and road chemicals.

Tires help ensure that ADAS technologies work at their best, according to Bendix. Drivers can double-check their wheel-ends for adequate tire tread depth and unusual wear like cracking. In the shop, technicians should make sure tire pressure monitoring systems are operating properly after the temperature swings of winter—running on the right inflation is critical.

You May Also Like

Fleet Advantage, FleetNet America by Cox Automotive partner on financing, maintenance solutions

An unbundled leases structure with finance and nationwide maintenance options.

Cox-Automotive-TMC-1400

Fleet Advantage, provider of specialty financing, fleet data analytics, fleet management services, and life cycle cost management, announced a collaboration with FleetNet America to facilitate fleet maintenance service offerings to organizations with transportation fleets that seek all the benefits of an unbundled lease structure with access to a maintenance provider with a nationwide network.

Good News! Parts, labor costs fell slightly Q4 2023

Decisiv, TMC Benchmarking Report shows trend reversal from previous quarter.

Decisiv-TMC-Benchmarking-Report-1400
Hunter Engineering to show HawkEye XL at TMC

Technician testimony appears to back up Hunter’s claims of increased alignment speed when using the HawkEye XL.

Hunter-HawkEye-XL-aligner-at-TMC
Navigating diesel engine oil usage uncertainties

The importance of tracking miles, monitoring oil levels and keeping accurate service records.

navigating-oil-usage-uncertainties
Southeastern Freight Lines promotes new service center manager

Keith Schneider has held various leadership positions with Southeastern, and will relocate to fulfill this new role.

Southeastern-freight-promotion-Keith-Schneider

Other Posts

Akebono launches severe-duty brake pads for Ford models

The company says its new brake pads last longer and can lower maintenance costs, while still providing the stopping power fleets need.

Truck maintenance recommendations for the spring season

Brian Screeton of Bendix talks about what maintenance practices fleets should put into place for their trucks, trailers and components during the spring.

OTR-Spring-Maintenance-1400
SAF-Holland Midland program adds automatic brake adjusters, ride height control valves

The Automatic Brake Adjusters and Ride Height Control Valves are part of the company’s Midland All-Makes Program.

SAF-HOLLAND-Midland-automatic-brake-adjusters-ride-height-control-valves
DMA Industries expands BrakeMaster wear sensors

The addition of 17 new OE replacement brake sensors now brings the BrakeMaster line up to a total of 264 products.

DMA-expands-BrakeMaster-brake-wear-sensors